Vector Boards 10,0 mm 1000x300mm VE3 Graupner 13300.10,0
BE A CREATOR
Let your fantasy, your imagination and your creativity run wild with the Graupner Vector Boards.
The new Vector Boards from Graupner offer you the opportunity to develop and build your own models according to your wishes.
Whether glider, remote-controlled aircraft model, vehicle model or stand model, the Vector Board is very versatile.
The Graupner Vector Board is more robust and tear-resistant than EPP and it will also be used in future on the Vector Line models.
Application examples are offered by the respective Vector Board strengths.
Go ahead and build your gliding model, download a 3-page view from the internet. Print them out and put them on the Vector Boards. Now just cut it out, add the eventually required trim weight, (can be a 1 or 2 euro-cents coin), paint and your own hand-launch glideris ready.
Print out the same view enlarged, so that the wing of the model corresponds approximately to the total area of an A4 paper sheet and experiment with the Vector Unit.
The Graupner Vector Board in thicknesses of 5-10 mm is ideally suited for indoor Parkfly model aircraft in the range below 500 g. The material is ideally suited to produce either wings or fuselages with carbon fiber reinforcement and tail planes or deep-drawn shell models.
Material Surface
We decided to make the Vector Board material as light as possible, since most of it is about flying. Since the Vector Board material is cast in blocks and then divided into the different thicknesses, the surface of the Vector Board may look slightly different depending on the thickness.
The casting creates a kind of ice crystal look with streaks in the surface.
The material thickness has a tolerance of +/- 0.1-0.3 mm.
Features:
- Light
- Pretty tough
- Finely pored
- Flexible
- Tear-resistant (except for sharp-edged cuts)
Processing:
The Vector Board can be cut with the cutter or a knife or sawed with a fretsaw (fretsaw with a fine blade).
You can glue the Vector Board with UHU por, hot glue or superglue.
You can paint it with feltpens, crayons, acrylic paints, universal paints, watercolors, digital printing.
If desired, you can also deep-draw the Vector Board to create more elaborate shapes. With the hot air blower, simple shapes can be bent.
Recommended accessories:
- Vector Core, 3 in 1 Receiver, Servo, Controller Unit No. 34001
- Vector Unit, 3 in 1 Unit - Drive Set No. 34002
- Vector Unit Extreme, 3 in 1 Unit - Drive Set No. 34003
- Remote control mz-4 HoTT, 2-channel No. S1031
- Receiver GR-12 SH +, HoTT, 6 channel No. 33565
- Digital servo DES 13 1 SH 11 mm No. 7902.SH
- Servo DS 121 Micro Servo No. S4102.SH
- Carbon fiber square bar 3x0.6x1000mm No. 5222.3.0,6
- Carbon fiber square bar 4x0,6x1000mm No. 5222.4.0,6
- Carbon fiber square rod 5x0.6x1000mm No. 5222.5.0,6
- Carbon fiber square rod 5x1,0x1000mm No. 5222.5.1
- Carbon fiber square bar 6x1,0x1000mm No. 5222.6.1,0
- Carbon fiber square rod 10x0,4x1000mm No. 5222.10.0,4
- Balsa cutter No. 980
- Replacement blades for balsa cutter No. 987
- Superglue viscous 20g No. 5821
- Activator for super glue 150ml No. 953150
- UHU Por 40g No. 959
Specification
Width [mm]: 300 mm
Weight [g]: 123 g
Piece / Pack: 3
Overall length [mm]: 1000 mm
Material: Vector Board
Basic pricing: 0.30 M2
de
en